Simple Timers

For many years, pulse-jet baghouses were cleaned by simple timers.  The timers would start the cleaning cycle every so many minutes.  You would be able to change how often your filters are cleaned by changing the time between each cleaning.  This design makes sure that the filters are cleaned regularly, whether they need to be cleaned or not.  The main issue with this is that every time a filter is cleaned, it increases the chances of it failing.  Filters are cleaned by pulsing high pressure air into the filter.  This expands the filter, which causes the top layers of dust to fall off.  But that expansion can also cause holes or rips in the filters.

Pulse-On-Demand Controller

So it would be beneficial to minimize the cleaning of the filters to only when it’s needed.  The pulse-on-demand controller does just this.  It measures the pressure drop across the filters.  When the pressure drop gets over a certain amount, it will begin the cleaning process.  Many of these controllers also have “bag break” technology, which will tell you when one of the filters has a hole.  You will then be able to replace the filters only when they are needed.  Some controllers can even isolate the row where the broken bag is located, so you won’t have to replace all the filters.

Installing a Clean-on-Demand controller, “bag break” technology, and cyclone pre-filters (Check out other Aerodyne blogs for more info) can help you decrease the maintenance on your filters, extend filter life, and lower operating costs (less air usage).

To learn more about which dust collector, please contact our experts at 440-543-7400 or visit our website: www.dustcollectorhq.com.

To improve efficiency and safety, there is no substitute for an on-site inspection by an experienced expert. Click below to start with a free 20-minute phone consultation by clicking the button.

If you are like many plant engineers who are working within the confines of a limited work space, rest assured that you don’t need to compromise on the efficiency of your industrial dust collection system. A traditional, high-efficiency cyclone is not the best solution for facilities with low ceilings.

Space Limitation

If space limitations prevent you from properly orienting this type of cyclone in an upright position, this will result in a loss of efficiency due to particulate settling on the side of the collector and being carried out with the exhaust gas. Attempting to solve this problem by installing your vertically oriented dust collection cyclone outdoors may encourage condensation that can shorten service life and reduce efficiency.

Horizontal Cyclones

Today, more plant engineers are choosing a horizontal configuration for reliable, high-efficiency dust collection. These options include the Aerodyne GPC Cyclone and counter-cyclonic dust collectors, such as the Aerodyne SplitStream™ Dust Collector.  The SplitStream™ Dust Collector uses a secondary air stream that directs material toward the collection hopper, and may be installed horizontally with virtually no loss of efficiency.

Because this design does not rely on gravity to bring the dust to the hopper like conventional cyclones, its operational efficiency is not affected by horizontal installation. In addition, this type of dust collection system may be suspended from a ceiling, conserving valuable space on the manufacturing floor.

The SplitStream™ Dust Collector the ability to increase/decrease process temperature while collecting dust. The unique counter cyclonic design element of the SplitStream™ Dust Collector ensures that a minimal amount of particulate comes in contact with the interior walls. This eliminates excessive wear and enables abrasive particulate collection.

How Do Horizontal Dust Collectors Work?

To learn more about which dust collector, please contact our experts at 440-543-7400 or visit our website: www.dustcollectorhq.com.

To improve efficiency and safety, there is no substitute for an on-site inspection by an experienced expert. Click below to start with a free 20-minute phone consultation by clicking the button.

As maintenance staffs become smaller and have less time to do preventative maintenance, technology needs to step in and help. 

Level Switches

That is where level switches in dust collector hoppers fit in.  An airlock works by allowing dust from the dust collector to leave the vessel while preventing air from leaking in or out of the system.  Some airlocks operate by emptying the hopper as soon as dust falls and some require a buildup above them to help seal the valve and provide motive force. 

The main thing is, that dust often times will not constantly be falling through the valve.  This means that walking next to a vessel won’t always tell you if the airlock is operating correctly. 

Installing a level switch in the hopper will help.  The level switch measures the amount of material in the hopper and if too much is in the hopper it will provide a signal (alarm).  This will tell maintenance that the airlock is not operating correctly and it needs to be investigated.  Depending on the system’s controls, the alarm can be a local alarm (light and/or horn) or feed into the central computer.

Dust collection systems can range from being fairly simple to extremely complex. 

It’s important to know that you have the proper system for your application. Some questions always come up when looking at dust collection systems.

To make life easier, we have put together some common questions we get asked along with answers and explanations. Have a look.

Volume 1:  

Volume 2:

To learn more about which dust collector, please contact our experts at 440-543-7400 or visit our website: www.dustcollectorhq.com.

To improve efficiency and safety, there is no substitute for an on-site inspection by an experienced expert. Click below to start with a free 20-minute phone consultation by clicking the button.

Heavy dust loading in the dust collector leads to high maintenance dust collectors.  Since most dust collectors are fabric filters (baghouse, cartridge collectors, shakers, etc.), heavy dust loading will cause/require high frequency of cleaning of the filters.  Most filters are cleaned by injecting high pressure air into the clean side, causing the filters to expand a bit.  This causes dust to fall off the filters.  Filters wear out due to the frequent expanding and contracting.  So the more often you have to clean a filter, the faster the filters will wear out.

Pleated Filters

This is made even worse if the filters are pleated.  Pleated filters have valleys and ridges which increase the surface area available for air to diffuse through the filter.  However, high dust loading can cause the pleated filter valleys to fill up and not properly clean during a cleaning cycle.  This will severely restrict the surface area available for airflow, which will lead to higher velocities through the filters.  A higher velocity increases the chances of dust getting through the filters.  This can cause holes to develop in the filter.  It can also cause dust to plug a pathway through the filter, thereby further restricting airflow.  It can also cause a decrease in removal efficiency.

So if you have high dust loading in your dust collector, it might be beneficial to install a pre-filter to increase filter life and make maintenance much less of a hassle.

Pre-filtering may reduce operating and maintenance costs by extending bag or filter life and improving removal efficiencies. This video discusses five warning signs that your dust collection system needs a pre-filter.

If you prefer this valuable information in white paper form, get our whitepaper, Top 5 Reasons to Use a Cyclone as a Pre-filter.

To learn more about which dust collector, please contact our experts at 440-543-7400 or visit our website: www.dustcollectorhq.com.

To improve efficiency and safety, there is no substitute for an on-site inspection by an experienced expert. Click below to start with a free 20-minute phone consultation by clicking the button.